diff --git a/creality-ender3/README.md b/creality-ender3/README.md
index 95032c7..a6b7813 100644
--- a/creality-ender3/README.md
+++ b/creality-ender3/README.md
@@ -286,7 +286,7 @@ make clean
 ```
 make menuconfig
 ```
-![Klipper firmaware build configuration](klipper/img/klipper-skr-mini-e3-v2-fw-config.png)
+![Klipper firmaware build configuration](klipper/images/klipper-skr-mini-e3-v2-fw-config.png)
 
 7. Build the firmaware:
 ```
@@ -311,13 +311,13 @@ sudo service klipper start
 ```
 sudo service klipper status
 ```
-![Klipper service status check](klipper/img/ender3-klipper-service-started.png)
+![Klipper service status check](klipper/images/ender3-klipper-service-started.png)
 
 
 ## ADXL345 accelorometer
 
 Model used: [Aliexpress](https://www.aliexpress.com/item/1005006515088013.html) \
-![Klipper ADXL345 config](klipper/img/klipper-adxl345-printer-config.png)
+![Klipper ADXL345 config](klipper/images/klipper-adxl345-printer-config.png)
 
 ### Software prereqiusites
 Note that resonance measurements and shaper auto-calibration require additional software dependencies not installed by default. First, run on your Raspberry Pi the following commands:
@@ -335,7 +335,7 @@ cd ~/klipper
 make clean
 make menuconfig
 ```
-![ADXL345 Firmare config](klipper/img/klipper-adxl345-fw-config.png)
+![ADXL345 Firmare config](klipper/images/klipper-adxl345-fw-config.png)
 
 2. Build the firmware:
 ```
@@ -349,7 +349,7 @@ make
 ```
 lsusb
 ```
-![ADXL345 board in DFU mode](klipper/img/ender3-adxl345-dfu-mode.png)
+![ADXL345 board in DFU mode](klipper/images/ender3-adxl345-dfu-mode.png)
 
 4. Note the device `ID` (in our example: `2e8a:0003`)
 
@@ -379,13 +379,13 @@ Retreive `idVendor` and `idProduct` for the Klipper MCU:
 ```
 lsusb
 ```
-![Find Klipper MCU ID](klipper/img/ender3-find-mcu-id.png)
+![Find Klipper MCU ID](klipper/images/ender3-find-mcu-id.png)
 
 2. Retrieve `idVendor` and `idProduct` using the Klipper MCU ID
 ```
 lsusb -v -d 1d50:614e | grep id
 ```
-![idVendor and idProduct](klipper/img/ender3-klipper-mcu-idvendor-idproduct.png)
+![idVendor and idProduct](klipper/images/ender3-klipper-mcu-idvendor-idproduct.png)
 
 Then add the following text into the `98-klipper.rules` file just created:
 
diff --git a/creality-ender3/klipper/img/ender3-adxl345-dfu-mode.png b/creality-ender3/klipper/images/ender3-adxl345-dfu-mode.png
similarity index 100%
rename from creality-ender3/klipper/img/ender3-adxl345-dfu-mode.png
rename to creality-ender3/klipper/images/ender3-adxl345-dfu-mode.png
diff --git a/creality-ender3/klipper/img/ender3-find-mcu-id.png b/creality-ender3/klipper/images/ender3-find-mcu-id.png
similarity index 100%
rename from creality-ender3/klipper/img/ender3-find-mcu-id.png
rename to creality-ender3/klipper/images/ender3-find-mcu-id.png
diff --git a/creality-ender3/klipper/img/ender3-klipper-mcu-idvendor-idproduct.png b/creality-ender3/klipper/images/ender3-klipper-mcu-idvendor-idproduct.png
similarity index 100%
rename from creality-ender3/klipper/img/ender3-klipper-mcu-idvendor-idproduct.png
rename to creality-ender3/klipper/images/ender3-klipper-mcu-idvendor-idproduct.png
diff --git a/creality-ender3/klipper/img/ender3-klipper-service-started.png b/creality-ender3/klipper/images/ender3-klipper-service-started.png
similarity index 100%
rename from creality-ender3/klipper/img/ender3-klipper-service-started.png
rename to creality-ender3/klipper/images/ender3-klipper-service-started.png
diff --git a/creality-ender3/klipper/img/klipper-adxl345-fw-config.png b/creality-ender3/klipper/images/klipper-adxl345-fw-config.png
similarity index 100%
rename from creality-ender3/klipper/img/klipper-adxl345-fw-config.png
rename to creality-ender3/klipper/images/klipper-adxl345-fw-config.png
diff --git a/creality-ender3/klipper/img/klipper-adxl345-printer-config.png b/creality-ender3/klipper/images/klipper-adxl345-printer-config.png
similarity index 100%
rename from creality-ender3/klipper/img/klipper-adxl345-printer-config.png
rename to creality-ender3/klipper/images/klipper-adxl345-printer-config.png
diff --git a/creality-ender3/klipper/img/klipper-skr-mini-e3-v2-fw-config.png b/creality-ender3/klipper/images/klipper-skr-mini-e3-v2-fw-config.png
similarity index 100%
rename from creality-ender3/klipper/img/klipper-skr-mini-e3-v2-fw-config.png
rename to creality-ender3/klipper/images/klipper-skr-mini-e3-v2-fw-config.png