From a135943daaaeb626def68731594f38377955a923 Mon Sep 17 00:00:00 2001 From: iGoX Date: Tue, 11 Feb 2025 18:42:17 +0100 Subject: [PATCH] Ender 3 - Sprite Pro Extruder --- .../Marlin-2.1.2.4/Marlin/Configuration.h | 36 +++++++++---------- .../Marlin-2.1.2.4/Marlin/Configuration_adv.h | 20 +++++------ 2 files changed, 28 insertions(+), 28 deletions(-) diff --git a/creality-ender3/Marlin-2.1.2.4/Marlin/Configuration.h b/creality-ender3/Marlin-2.1.2.4/Marlin/Configuration.h index 9dfa0f8..a51ce6d 100644 --- a/creality-ender3/Marlin-2.1.2.4/Marlin/Configuration.h +++ b/creality-ender3/Marlin-2.1.2.4/Marlin/Configuration.h @@ -634,7 +634,7 @@ // Above this temperature the heater will be switched off. // This can protect components from overheating, but NOT from shorts and failures. // (Use MINTEMP for thermistor short/failure protection.) -#define HEATER_0_MAXTEMP 315 // MBO: Original 275 / Sprite Pro 315 +#define HEATER_0_MAXTEMP 300 // MBO: Original 275 / Sprite Pro 300 #define HEATER_1_MAXTEMP 275 #define HEATER_2_MAXTEMP 275 #define HEATER_3_MAXTEMP 275 @@ -855,7 +855,7 @@ * Note: For Bowden Extruders make this large enough to allow load/unload. */ #define PREVENT_LENGTHY_EXTRUDE -#define EXTRUDE_MAXLENGTH 200 // MBO: Original value: 600 / Sprite Pro: 200 +#define EXTRUDE_MAXLENGTH 600 // MBO: To be decrease with Sprite Pro? //=========================================================================== //======================== Thermal Runaway Protection ======================= @@ -1244,7 +1244,7 @@ * When changing speed and direction, if the difference is less than the * value set here, it may happen instantaneously. */ -#define CLASSIC_JERK +//#define CLASSIC_JERK #if ENABLED(CLASSIC_JERK) #define DEFAULT_XJERK 10.0 #define DEFAULT_YJERK 10.0 @@ -1520,7 +1520,7 @@ // Most probes should stay away from the edges of the bed, but // with NOZZLE_AS_PROBE this can be negative for a wider probing area. -#define PROBING_MARGIN 15 +#define PROBING_MARGIN 10 // MBO: change from 15 to 10 // X and Y axis travel speed (mm/min) between probes #define XY_PROBE_FEEDRATE (133*60) @@ -1631,10 +1631,10 @@ //#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors // Require minimum nozzle and/or bed temperature for probing -//#define PREHEAT_BEFORE_PROBING +#define PREHEAT_BEFORE_PROBING // MBO: enable #if ENABLED(PREHEAT_BEFORE_PROBING) - #define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time - #define PROBING_BED_TEMP 50 + #define PROBING_NOZZLE_TEMP 150 // (°C) Only applies to E0 at this time // MBO: change from 120 to 150 + #define PROBING_BED_TEMP 60 // MBO: change from 50 to 60 #endif // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 @@ -1872,7 +1872,7 @@ // After a runout is detected, continue printing this length of filament // before executing the runout script. Useful for a sensor at the end of // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead. - #define FILAMENT_RUNOUT_DISTANCE_MM 8 + #define FILAMENT_RUNOUT_DISTANCE_MM 8 // MBO: to be changed after Sprite Pro and new filament sensor installation #ifdef FILAMENT_RUNOUT_DISTANCE_MM // Enable this option to use an encoder disc that toggles the runout pin @@ -1943,10 +1943,10 @@ /** * Auto-leveling needs preheating */ -#define PREHEAT_BEFORE_LEVELING +//#define PREHEAT_BEFORE_LEVELING #if ENABLED(PREHEAT_BEFORE_LEVELING) #define LEVELING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time - #define LEVELING_BED_TEMP 50 + #define LEVELING_BED_TEMP 60 // #endif /** @@ -2150,7 +2150,7 @@ #define HOMING_FEEDRATE_MM_M { (20*60), (20*60), (4*60) } // Validate that endstops are triggered on homing moves -#define VALIDATE_HOMING_ENDSTOPS +#define VALIDATE_HOMING_ENDSTOPS // MBO: enable // @section calibrate @@ -2416,7 +2416,7 @@ * * View the current statistics with M78. */ -//#define PRINTCOUNTER +#define PRINTCOUNTER // MBO: enable #if ENABLED(PRINTCOUNTER) #define PRINTCOUNTER_SAVE_INTERVAL 60 // (minutes) EEPROM save interval during print. A value of 0 will save stats at end of print. #endif @@ -3354,17 +3354,17 @@ #endif // Support for Adafruit NeoPixel LED driver -#define NEOPIXEL_LED +#define NEOPIXEL_LED // MBO: enable #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW, NEO_RGBW, NEO_GRB, NEO_RBG, etc. // See https://github.com/adafruit/Adafruit_NeoPixel/blob/master/Adafruit_NeoPixel.h - #define NEOPIXEL_PIN PA8 // LED driving pin + #define NEOPIXEL_PIN PA8 // MBO: LED driving pin for BBT SKR E3 Mini v2.0 //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE //#define NEOPIXEL2_PIN 5 - #define NEOPIXEL_PIXELS 17 // Number of LEDs in the strip. (Longest strip when NEOPIXEL2_SEPARATE is disabled.) - #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. - #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) - #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + #define NEOPIXEL_PIXELS 17 // Number of LEDs in the strip. (Longest strip when NEOPIXEL2_SEPARATE is disabled.) // MBO: 17 + //#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) // MBO: 127 + #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup // MBO: enable // Support for second Adafruit NeoPixel LED driver controlled with M150 S1 ... //#define NEOPIXEL2_SEPARATE diff --git a/creality-ender3/Marlin-2.1.2.4/Marlin/Configuration_adv.h b/creality-ender3/Marlin-2.1.2.4/Marlin/Configuration_adv.h index bddf765..12c5fa0 100644 --- a/creality-ender3/Marlin-2.1.2.4/Marlin/Configuration_adv.h +++ b/creality-ender3/Marlin-2.1.2.4/Marlin/Configuration_adv.h @@ -50,7 +50,7 @@ * 3 = schema.json - The entire configuration schema. (13 = pattern groups) * 4 = schema.yml - The entire configuration schema. */ -//#define CONFIG_EXPORT 2 // :[1:'JSON', 2:'config.ini', 3:'schema.json', 4:'schema.yml'] +#define CONFIG_EXPORT 1 // :[1:'JSON', 2:'config.ini', 3:'schema.json', 4:'schema.yml'] //=========================================================================== //============================= Thermal Settings ============================ @@ -1032,21 +1032,21 @@ // // Add the G35 command to read bed corners to help adjust screws. Requires a bed probe. // -#define ASSISTED_TRAMMING +#define ASSISTED_TRAMMING // MBO: enable #if ENABLED(ASSISTED_TRAMMING) // Define from 3 to 9 points to probe. //#define TRAMMING_POINT_XY { { 35, 30 }, { 205, 30 }, { 205, 205 }, { 35, 205 } } - #define TRAMMING_POINT_XY { { 35, 30 }, { 180, 30 }, { 180, 200 }, { 35, 200 } } + #define TRAMMING_POINT_XY { { 35, 200 }, { 35, 30 }, { 180, 30 }, { 180, 200 } } // Define position names for probe points. - #define TRAMMING_POINT_NAME_1 "Front-Left" - #define TRAMMING_POINT_NAME_2 "Front-Right" - #define TRAMMING_POINT_NAME_3 "Back-Right" - #define TRAMMING_POINT_NAME_4 "Back-Left" + #define TRAMMING_POINT_NAME_1 "Back-Left" + #define TRAMMING_POINT_NAME_2 "Front-Left" + #define TRAMMING_POINT_NAME_3 "Front-Right" + #define TRAMMING_POINT_NAME_4 "Back-Right" #define RESTORE_LEVELING_AFTER_G35 // Enable to restore leveling setup after operation - //#define REPORT_TRAMMING_MM // Report Z deviation (mm) for each point relative to the first + #define REPORT_TRAMMING_MM // Report Z deviation (mm) for each point relative to the first // MBO: enable #define ASSISTED_TRAMMING_WIZARD // Add a Tramming Wizard to the LCD menu @@ -2657,7 +2657,7 @@ // This short retract is done immediately, before parking the nozzle. #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 50 // (mm/s) Unload filament feedrate. This can be pretty fast. #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. - #define FILAMENT_CHANGE_UNLOAD_LENGTH 400 // (mm) The length of filament for a complete unload. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 40 // (mm) The length of filament for a complete unload. // MBO: change from 400 to 40 // For Bowden, the full length of the tube and nozzle. // For direct drive, the full length of the nozzle. // Set to 0 for manual unloading. @@ -2666,7 +2666,7 @@ // 0 to disable start loading and skip to fast load only #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 60 // (mm/s) Load filament feedrate. This can be pretty fast. #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. - #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 400 // (mm) Load length of filament, from extruder gear to nozzle. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 40 // (mm) Load length of filament, from extruder gear to nozzle. // MBO: change from 400 to 40 // For Bowden, the full length of the tube and nozzle. // For direct drive, the full length of the nozzle. //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.