diff --git a/creality-ender3/Klipper/config/adxl345.cfg b/creality-ender3/Klipper/config/adxl345.cfg deleted file mode 100644 index 1a7c741..0000000 --- a/creality-ender3/Klipper/config/adxl345.cfg +++ /dev/null @@ -1,23 +0,0 @@ -[mcu x_adxl] -# Change to whatever you found above. For example, -# usb-Klipper_rp2040_E661640843545B2E-if00 -serial: /dev/serial/by-path/platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.1:1.0 - - - -[adxl345] -cs_pin: x_adxl:gpio9 -spi_software_sclk_pin: x_adxl:gpio10 -spi_software_mosi_pin: x_adxl:gpio11 -spi_software_miso_pin: x_adxl:gpio12 - -axes_map: y,x,-z # x,z,y - -[resonance_tester] -accel_chip: adxl345 -probe_points: - # Somewhere slightly above the middle of your print bed - 150,150, 20 - -#[output_pin power_mode] # Improve power stability -#pin: adxl:gpio23 \ No newline at end of file diff --git a/creality-ender3/Klipper/config/klipper-config-files-20250305-150641.zip b/creality-ender3/Klipper/config/klipper-config-files-20250305-150641.zip new file mode 100644 index 0000000..7544317 Binary files /dev/null and b/creality-ender3/Klipper/config/klipper-config-files-20250305-150641.zip differ diff --git a/creality-ender3/Klipper/config/led-progress.cfg b/creality-ender3/Klipper/config/led-progress.cfg deleted file mode 100644 index f5666f2..0000000 --- a/creality-ender3/Klipper/config/led-progress.cfg +++ /dev/null @@ -1,117 +0,0 @@ -# use NEOPIXEL_DISPLAY LED=Led_Name TYPE=template_type MODE=template_mode - -# for TYPE use: -# extruder_temp :extruder temperature progress -# bed_temp :bed temperature progress -# print_percent :print progress -# printer_speed :printer speed - -# for MODE use: -# progress :the leds will light up one by one -# glow :all leds will fade from one color (or non) to other color - -# more info: https://github.com/digitalninja-ro/klipper-neopixel/blob/master/README.md - -[gcode_macro NEOPIXEL_DISPLAY] -gcode: - {% set led = params.LED %} - {% set type = params.TYPE %} - {% set mode = params.MODE %} - {% set my_neopixel = printer.configfile.config['neopixel ' ~ led] %} - - {% if mode == 'progress' %} - {% for i in range(my_neopixel.chain_count|int) %} - SET_LED_TEMPLATE LED={led} INDEX={i+1} TEMPLATE={'led_' ~ type ~ '_' ~ mode} param_led_num={i+1} param_led_total={my_neopixel.chain_count|int} - {% endfor %} - {% endif %} - {% if mode == 'glow' %} - SET_LED_TEMPLATE LED={led} TEMPLATE={'led_' ~ type ~ '_' ~ mode} - {% endif %} - -[display_template led_extruder_temp_glow] -text: - {% if printer.extruder.target > 0.0 %} - {% set temp = printer.extruder.target %} - {% else %} - {% set temp = printer.configfile.config.extruder.max_temp %} - {% endif %} - {% set ratio = printer.extruder.temperature / temp|float %} - {ratio}, 0.0, {1-ratio}, 0.0 - -[display_template led_extruder_temp_progress] -param_led_num: 0 -param_led_total: 1 -text: - {% if printer.extruder.target > 0.0 %} - {% set temp = printer.extruder.target %} - {% else %} - {% set temp = printer.configfile.config.extruder.max_temp %} - {% endif %} - {% set ratio = printer.extruder.temperature / temp|float %} - {% set led_ratio = param_led_num|float / param_led_total %} - {% if ratio > led_ratio %} - {led_ratio}, 0.0, 0.0, 0.0 - {% else %} - 0.0, 0.0, 0.0, 0.0 - {% endif %} - -[display_template led_bed_temp_glow] -text: - {% if printer.heater_bed.target > 0.0 %} - {% set temp = printer.heater_bed.target %} - {% else %} - {% set temp = printer.configfile.config.heater_bed.max_temp %} - {% endif %} - {% set ratio = printer.heater_bed.temperature / temp|float %} - {ratio}, 0.0, {1-ratio}, 0.0 - -[display_template led_bed_temp_progress] -param_led_num: 0 -param_led_total: 1 -text: - {% if printer.heater_bed.target > 0.0 %} - {% set temp = printer.heater_bed.target %} - {% else %} - {% set temp = printer.configfile.config.heater_bed.max_temp %} - {% endif %} - {% set ratio = printer.heater_bed.temperature / temp|float %} - {% set led_ratio = param_led_num|float / param_led_total %} - {% if ratio > led_ratio %} - {led_ratio}, 0.0, 0.0, 0.0 - {% else %} - 0.0, 0.0, 0.0, 0.0 - {% endif %} - -[display_template led_print_percent_glow] -text: - {% set ratio = printer.virtual_sdcard.progress %} - 0.0, {ratio}, 0.0, 0.0 - -[display_template led_print_percent_progress] -param_led_num: 0 -param_led_total: 1 -text: - {% set ratio = printer.virtual_sdcard.progress %} - {% set led_ratio = param_led_num|float / param_led_total %} - {% if ratio > led_ratio %} - 0.0, {led_ratio}, 0.0, 0.0 - {% else %} - 0.0, 0.0, 0.0, 0.0 - {% endif %} - -[display_template led_printer_speed_glow] -text: - {% set ratio = printer.motion_report.live_velocity|float / printer.configfile.config.printer.max_velocity|float %} - 0.0, {ratio}, 0.0, 0.0 - -[display_template led_printer_speed_progress] -param_led_num: 0 -param_led_total: 1 -text: - {% set ratio = printer.motion_report.live_velocity|float / printer.configfile.config.printer.max_velocity|float %} - {% set led_ratio = param_led_num|float / param_led_total %} - {% if ratio > led_ratio %} - 0.0, {led_ratio}, 0.0, 0.0 - {% else %} - 0.0, 0.0, 0.0, 0.0 - {% endif %} \ No newline at end of file diff --git a/creality-ender3/Klipper/config/macros.cfg b/creality-ender3/Klipper/config/macros.cfg deleted file mode 100644 index 62c8c8c..0000000 --- a/creality-ender3/Klipper/config/macros.cfg +++ /dev/null @@ -1,188 +0,0 @@ -[gcode_macro START_PRINT] -gcode: - #Get Bed and Extruder temperature from Slicer GCode - {% set BED_TEMP = params.BED_TEMP|default(60)|float %} - {% set EXTRUDER_TEMP = params.EXTRUDER_TEMP|default(200)|float %} - - CLEAR_PAUSE - G90 - - ELED_ON - - M117 Heatup Bed {BED_TEMP} degres Nozzle {EXTRUDER_TEMP} degres - - SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={BED_TEMP} - TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={BED_TEMP*0.96} MAXIMUM={BED_TEMP*1.04} - SET_HEATER_TEMPERATURE HEATER=extruder TARGET={EXTRUDER_TEMP} - - G28 - - BED_MESH_PROFILE LOAD=default - - G1 Z10 F3000 ; move z up little to prevent scratching of surface - G1 X2 Y2 Z10 F5000.0 ; move to start-line position - - TEMPERATURE_WAIT SENSOR=extruder MINIMUM={EXTRUDER_TEMP*0.98} MAXIMUM={EXTRUDER_TEMP*1.02} - - PRIME_LINE - - M117 - -[gcode_macro END_PRINT] -gcode: - ELED_OFF - - M117 End print - TURN_OFF_HEATERS - - M117 Present print - PRESENT_PRINT - - M117 - M84 - -[gcode_macro PRIME_LINE] -gcode: - SAVE_GCODE_STATE NAME=prime_line_state - - #Precondition extruder - G92 E0 ; reset extruder - G1 X2 Y20 Z1.0 F4000.0 ; move to start-line position - G1 X2 Y20 Z0.3 F300.0 ; move z up little to prevent scratching of surface - G1 X2 Y200.0 Z0.3 F1500.0 E15 ; draw 1st line - G1 X2 Y200.0 Z0.4 F5000.0 ; move to side a little - G1 X2 Y20 Z0.4 F1500.0 E30 ; draw 2nd line - G92 E0 ; reset extruder - G1 Z1.0 F300 ; move z up little to prevent scratching of surface - - RESTORE_GCODE_STATE NAME=prime_line_state - -[gcode_macro PRESENT_PRINT] -gcode: - SAVE_GCODE_STATE NAME=present_print_state - - {% set X_MAX = printer.toolhead.axis_maximum.x|float %} - {% set Y_MAX = printer.toolhead.axis_maximum.y|float %} - {% set Z_MAX = printer.toolhead.axis_maximum.z|float %} - {% set Z_PARK_MIN = 100 | float %} - {% set Z_PARK_LIFT = 10 | float %} - - # Move nozzle away from print while retracting - G91 - G1 E-3 F300 - - G90 - {% if printer.toolhead.position.z + Z_PARK_LIFT > Z_PARK_MIN %} - G1 X{X_MAX / 2} Y{Y_MAX * 0.8} Z{printer.toolhead.position.z + Z_PARK_LIFT} F4000 - {% else %} - G1 X{X_MAX / 2} Y{Y_MAX * 0.8} Z{Z_PARK_MIN} F4000 - {% endif %} - - RESTORE_GCODE_STATE NAME=present_print_state - -[gcode_macro PAUSE] -description: Pause the actual running print -rename_existing: PAUSE_BASE -gcode: - PAUSE_BASE - - SET_ELED RED=0.0 GREEN=1.0 BLUE=1.0 - - _TOOLHEAD_PARK_PAUSE_CANCEL - -[gcode_macro RESUME] -description: Resume the actual running print -rename_existing: RESUME_BASE -gcode: - ##### read extrude from _TOOLHEAD_PARK_PAUSE_CANCEL macro ##### - {% set extrude = printer['gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL'].extrude %} - #### get VELOCITY parameter if specified #### - {% if 'VELOCITY' in params|upper %} - {% set get_params = ('VELOCITY=' + params.VELOCITY) %} - {%else %} - {% set get_params = "" %} - {% endif %} - ##### end of definitions ##### - {% if printer.extruder.can_extrude|lower == 'true' %} - M83 - G1 E{extrude} F2100 - {% if printer.gcode_move.absolute_extrude |lower == 'true' %} M82 {% endif %} - {% else %} - {action_respond_info("Extruder not hot enough")} - {% endif %} - - ELED_ON - - RESUME_BASE {get_params} - -[gcode_macro CANCEL_PRINT] -description: Cancel the actual running print -rename_existing: CANCEL_PRINT_BASE -variable_park: True -gcode: - ## Move head and retract only if not already in the pause state and park set to true - {% if printer.pause_resume.is_paused|lower == 'false' and park|lower == 'true'%} - _TOOLHEAD_PARK_PAUSE_CANCEL - {% endif %} - TURN_OFF_HEATERS - - SET_ELED RED=1.0 GREEN=1.0 - - CANCEL_PRINT_BASE - -[gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL] -description: Helper: park toolhead used in PAUSE and CANCEL_PRINT -variable_extrude: 1.0 -gcode: - ##### set park positon for x and y ##### - # default is your max posion from your printer.cfg - {% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %} - {% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %} - {% set z_park_delta = 2.0 %} - ##### calculate save lift position ##### - {% set max_z = printer.toolhead.axis_maximum.z|float %} - {% set act_z = printer.toolhead.position.z|float %} - {% if act_z < (max_z - z_park_delta) %} - {% set z_safe = z_park_delta %} - {% else %} - {% set z_safe = max_z - act_z %} - {% endif %} - ##### end of definitions ##### - {% if printer.extruder.can_extrude|lower == 'true' %} - M83 - G1 E-{extrude} F2100 - {% if printer.gcode_move.absolute_extrude |lower == 'true' %} M82 {% endif %} - {% else %} - {action_respond_info("Extruder not hot enough")} - {% endif %} - {% if "xyz" in printer.toolhead.homed_axes %} - G91 - G1 Z{z_safe} F900 - G90 - G1 X{x_park} Y{y_park} F6000 - {% if printer.gcode_move.absolute_coordinates|lower == 'false' %} G91 {% endif %} - {% else %} - {action_respond_info("Printer not homed")} - {% endif %} - -[gcode_macro ELED_ON] -description: Turn extruder LED on and resets led colors -gcode: - SET_ELED RED=1.0 GREEN=1.0 BLUE=1.0 - -[gcode_macro ELED_OFF] -description: Turn extruder LED strip off -gcode: - SET_ELED RED=0.0 GREEN=0.0 BLUE=0.0 - -[gcode_macro SET_ELED] -description: SET_LED extruder shortcut -#rename_existing: SET_LED_BASE -gcode: - {% set RED = params.RED|default(0)|float %} - {% set GREEN = params.GREEN|default(0)|float %} - {% set BLUE = params.BLUE|default(0)|float %} - {% set WHITE = params.BLUE|default(0)|float %} - - SET_LED LED=extruder RED={RED} GREEN={GREEN} BLUE={BLUE} WHITE={WHITE} - \ No newline at end of file diff --git a/creality-ender3/Klipper/config/printer.cfg b/creality-ender3/Klipper/config/printer.cfg deleted file mode 100644 index 5b3699d..0000000 --- a/creality-ender3/Klipper/config/printer.cfg +++ /dev/null @@ -1,259 +0,0 @@ -# Paste here and save your klipper configuration -# This file contains common pin mappings for the BIGTREETECH SKR mini -# E3 v2.0. To use this config, the firmware should be compiled for the -# STM32F103 with a "28KiB bootloader" and USB communication. Also, -# select "Enable extra low-level configuration options" and configure -# "GPIO pins to set at micro-controller startup" to "!PA14". - -# The "make flash" command does not work on the SKR mini E3. Instead, -# after running "make", copy the generated "out/klipper.bin" file to a -# file named "firmware.bin" on an SD card and then restart the SKR -# mini E3 with that SD card. - -# See docs/Config_Reference.md for a description of parameters. - -# Inpput shaper auto-calibration: -# accelerometer configuration -#[include adxl345.cfg] - -# [include macros.cfg] - -[mcu] -serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_37FFD9054252353440740557-if00 - -[printer] -kinematics: cartesian -max_velocity: 300 -max_accel: 3000 -max_z_velocity: 50 -max_z_accel: 400 -square_corner_velocity: 5.0 - -[stepper_x] -step_pin: PB13 -dir_pin: !PB12 -enable_pin: !PB14 -microsteps: 16 -rotation_distance: 40 -endstop_pin: ^PC0 -position_endstop: 0 -position_max: 220 -homing_retract_dist: 5.0 -homing_speed: 40 -homing_retract_dist: 5.0 -second_homing_speed: 2 - -[tmc2209 stepper_x] -uart_pin: PC11 -tx_pin: PC10 -uart_address: 0 -run_current: 0.580 -stealthchop_threshold: 999999 - -[stepper_y] -step_pin: PB10 -dir_pin: !PB2 -enable_pin: !PB11 -microsteps: 16 -rotation_distance: 40 -endstop_pin: ^PC1 -position_endstop: 0 -position_max: 220 -homing_speed: 40 -homing_retract_dist: 5.0 -second_homing_speed: 2 - -[tmc2209 stepper_y] -uart_pin: PC11 -tx_pin: PC10 -uart_address: 2 -run_current: 0.580 -stealthchop_threshold: 999999 - -[stepper_z] -step_pin: PB0 -dir_pin: PC5 -enable_pin: !PB1 -microsteps: 16 -rotation_distance: 8 -# endstop_pin: ^PC2 -endstop_pin: probe:z_virtual_endstop -# position_endstop: 0.0 -position_min: -2 -position_max: 250 -homing_speed: 10 -homing_retract_dist: 5.0 -second_homing_speed: 2 - -[tmc2209 stepper_z] -uart_pin: PC11 -tx_pin: PC10 -uart_address: 1 -run_current: 0.580 -stealthchop_threshold: 999999 - -[extruder] -step_pin: PB3 -dir_pin: !PB4 -enable_pin: !PD2 -microsteps: 16 -rotation_distance: 33.683 -nozzle_diameter: 0.400 -filament_diameter: 1.750 -heater_pin: PC8 -sensor_type: EPCOS 100K B57560G104F -sensor_pin: PA0 -control: pid -pid_Kp: 21.527 -pid_Ki: 1.063 -pid_Kd: 108.982 -min_temp: 0 -max_temp: 250 - -[tmc2209 extruder] -uart_pin: PC11 -tx_pin: PC10 -uart_address: 3 -run_current: 0.650 -stealthchop_threshold: 999999 - -[heater_bed] -heater_pin: PC9 -sensor_type: ATC Semitec 104GT-2 -sensor_pin: PC3 -control: pid -pid_Kp: 54.027 -pid_Ki: 0.770 -pid_Kd: 948.182 -min_temp: 0 -max_temp: 130 - -[heater_fan extruder] -# fan on hotend/extruder -pin: PC7 -heater: extruder - -[fan] -# filament_cooling -pin: PC6 -off_below: 0.1 - -[bed_screws] -# Nozzle / Screws alignment -screw1_name: front left -screw1: 25,35 -screw2_name: front right -screw2: 195,35 -screw3_name: back right -screw3: 197,200 -screw4_name: back left -screw4: 27,205 -speed: 100.0 - -[bltouch] -sensor_pin: PC2 -control_pin: PA1 -x_offset:-51 -y_offset:-12 -z_offset = 3.0 -speed:5 -samples: 3 -samples_result: average -samples_tolerance: 0.050 -samples_tolerance_retries: 3 - -[safe_z_home] -home_xy_position: 161,122 -z_hop: 15 - -[screws_tilt_adjust] -# BLTouch / Screws alignment -screw1_name: front left -screw1: 76,47 -screw2_name: front right -screw2: 220,47 -screw3_name: back left -screw3: 220,212 -screw4_name: back right -screw4: 79,217 -speed: 100.0 -screw_thread: CW-M4 - -[bed_mesh] -speed: 100 -mesh_min: 29.25, 12.8 -mesh_max: 272.75, 263 -algorithm: bicubic -probe_count: 5,5 -mesh_pps: 3 -fade_start: 1 -fade_end: 10 - -[neopixel lightbar] -pin: PA8 -chain_count: 17 -initial_RED: 1.0 -initial_GREEN: 1.0 -initial_BLUE: 1.0 - - -###################################################################### -# 128x64 Full Graphic Creality CR10 / ENDER 3 stockdisplay -# https://github.com/Klipper3d/klipper/blob/master/config/sample-lcd.cfg -###################################################################### - -# This section is used for a Creality "12864" display with a single -# ribbon cable between the display's EXP3 plug and the -# micro-controller board's EXP1 connector. - -# [display] -# lcd_type: st7920 -# cs_pin: EXP1_7 -# sclk_pin: EXP1_6 -# sid_pin: EXP1_8 -# encoder_pins: ^EXP1_5, ^EXP1_3 -# click_pin: ^!EXP1_2 - -# [output_pin beeper] -# pin: EXP1_1 - -###################################################################### - -[display] -lcd_type: st7920 -cs_pin: PB8 -sclk_pin: PB9 -sid_pin: PB15 -encoder_pins: ^PA10, ^PA9 -click_pin: ^!PA15 - -[output_pin beeper] -pin: PB5 - - - -# [filament_switch_sensor filament] -# pause_on_runout: True # Starts the PAUSE g-code script if filament runs out -# runout_gcode: M117 Filament runout # Optional -# insert_gcode: M117 Filament insert # Optional -# switch_pin: PC15 # - -# Support for M117 gcode (message display) -[display_status] - -[static_digital_output usb_pullup_enable] -pins: !PA14 - -[board_pins] -aliases: - # EXP1 header - EXP1_1=PB5, EXP1_2=PA15, - EXP1_3=PA9, EXP1_4=, - EXP1_5=PA10, EXP1_6=PB9, - EXP1_7=PB8, EXP1_8=PB15, - EXP1_9=, EXP1_10=<5V> - - - - -# See the sample-lcd.cfg file for definitions of common LCD displays. diff --git a/creality-ender3/Klipper/firmware/2024-01-22-firmware.bin b/creality-ender3/Klipper/firmware/2024-01-22-firmware.bin deleted file mode 100644 index 6c1d490..0000000 Binary files a/creality-ender3/Klipper/firmware/2024-01-22-firmware.bin and /dev/null differ diff --git a/creality-ender3/README.md b/creality-ender3/README.md index 53d8f8a..53de0a8 100644 --- a/creality-ender3/README.md +++ b/creality-ender3/README.md @@ -247,6 +247,10 @@ After firware update, proceed with the different calibrations in the above order # Klipper custom firmware +## Klipper configuration backup +2025-03-05 : [klipper-config-files-20250305-150641.zip](klipper/config/klipper-config-files-20250305-150641.zip) +- Initial config save + ## Printer firmware build and update 1. Access klipper host using ssh ```