iGoX/3d-printers
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

Prepare firmware modifications for Spite Pro extruder upgrade #19

Merged
iGoX merged 9 commits from igox/ender3-sprite-pro-extruder into main 2025-02-11 19:42:37 +01:00
Conversation 0 Commits 9 Files Changed 2 +28 -28
2 changed files with 28 additions and 28 deletions
Download Patch File Download Diff File Expand all files Collapse all files
Showing only changes of commit a135943daa - Show all commits

36
creality-ender3/Marlin-2.1.2.4/Marlin/Configuration.h
View File

@@ -634,7 +634,7 @@
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
// (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 315 // MBO: Original 275 / Sprite Pro 315
#define HEATER_0_MAXTEMP 300 // MBO: Original 275 / Sprite Pro 300
#define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
@@ -855,7 +855,7 @@
* Note: For Bowden Extruders make this large enough to allow load/unload.
*/
#define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH 200 // MBO: Original value: 600 / Sprite Pro: 200
#define EXTRUDE_MAXLENGTH 600 // MBO: To be decrease with Sprite Pro?
//===========================================================================
//======================== Thermal Runaway Protection =======================
@@ -1244,7 +1244,7 @@
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define CLASSIC_JERK
//#define CLASSIC_JERK
#if ENABLED(CLASSIC_JERK)
#define DEFAULT_XJERK 10.0
#define DEFAULT_YJERK 10.0
@@ -1520,7 +1520,7 @@
// Most probes should stay away from the edges of the bed, but
// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define PROBING_MARGIN 15
#define PROBING_MARGIN 10 // MBO: change from 15 to 10
// X and Y axis travel speed (mm/min) between probes
#define XY_PROBE_FEEDRATE (133*60)
@@ -1631,10 +1631,10 @@
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
// Require minimum nozzle and/or bed temperature for probing
//#define PREHEAT_BEFORE_PROBING
#define PREHEAT_BEFORE_PROBING // MBO: enable
#if ENABLED(PREHEAT_BEFORE_PROBING)
#define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time
#define PROBING_BED_TEMP 50
#define PROBING_NOZZLE_TEMP 150 // (°C) Only applies to E0 at this time // MBO: change from 120 to 150
#define PROBING_BED_TEMP 60 // MBO: change from 50 to 60
#endif
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@@ -1872,7 +1872,7 @@
// After a runout is detected, continue printing this length of filament
// before executing the runout script. Useful for a sensor at the end of
// a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
#define FILAMENT_RUNOUT_DISTANCE_MM 8
#define FILAMENT_RUNOUT_DISTANCE_MM 8 // MBO: to be changed after Sprite Pro and new filament sensor installation
#ifdef FILAMENT_RUNOUT_DISTANCE_MM
// Enable this option to use an encoder disc that toggles the runout pin
@@ -1943,10 +1943,10 @@
/**
* Auto-leveling needs preheating
*/
#define PREHEAT_BEFORE_LEVELING
//#define PREHEAT_BEFORE_LEVELING
#if ENABLED(PREHEAT_BEFORE_LEVELING)
#define LEVELING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time
#define LEVELING_BED_TEMP 50
#define LEVELING_BED_TEMP 60 //
#endif
/**
@@ -2150,7 +2150,7 @@
#define HOMING_FEEDRATE_MM_M { (20*60), (20*60), (4*60) }
// Validate that endstops are triggered on homing moves
#define VALIDATE_HOMING_ENDSTOPS
#define VALIDATE_HOMING_ENDSTOPS // MBO: enable
// @section calibrate
@@ -2416,7 +2416,7 @@
*
* View the current statistics with M78.
*/
//#define PRINTCOUNTER
#define PRINTCOUNTER // MBO: enable
#if ENABLED(PRINTCOUNTER)
#define PRINTCOUNTER_SAVE_INTERVAL 60 // (minutes) EEPROM save interval during print. A value of 0 will save stats at end of print.
#endif
@@ -3354,17 +3354,17 @@
#endif
// Support for Adafruit NeoPixel LED driver
#define NEOPIXEL_LED
#define NEOPIXEL_LED // MBO: enable
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW, NEO_RGBW, NEO_GRB, NEO_RBG, etc.
// See https://github.com/adafruit/Adafruit_NeoPixel/blob/master/Adafruit_NeoPixel.h
#define NEOPIXEL_PIN PA8 // LED driving pin
#define NEOPIXEL_PIN PA8 // MBO: LED driving pin for BBT SKR E3 Mini v2.0
//#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
//#define NEOPIXEL2_PIN 5
#define NEOPIXEL_PIXELS 17 // Number of LEDs in the strip. (Longest strip when NEOPIXEL2_SEPARATE is disabled.)
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#define NEOPIXEL_PIXELS 17 // Number of LEDs in the strip. (Longest strip when NEOPIXEL2_SEPARATE is disabled.) // MBO: 17
//#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) // MBO: 127
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup // MBO: enable
// Support for second Adafruit NeoPixel LED driver controlled with M150 S1 ...
//#define NEOPIXEL2_SEPARATE

20
creality-ender3/Marlin-2.1.2.4/Marlin/Configuration_adv.h
View File

@@ -50,7 +50,7 @@
* 3 = schema.json - The entire configuration schema. (13 = pattern groups)
* 4 = schema.yml - The entire configuration schema.
*/
//#define CONFIG_EXPORT 2 // :[1:'JSON', 2:'config.ini', 3:'schema.json', 4:'schema.yml']
#define CONFIG_EXPORT 1 // :[1:'JSON', 2:'config.ini', 3:'schema.json', 4:'schema.yml']
//===========================================================================
//============================= Thermal Settings ============================
@@ -1032,21 +1032,21 @@
//
// Add the G35 command to read bed corners to help adjust screws. Requires a bed probe.
//
#define ASSISTED_TRAMMING
#define ASSISTED_TRAMMING // MBO: enable
#if ENABLED(ASSISTED_TRAMMING)
// Define from 3 to 9 points to probe.
//#define TRAMMING_POINT_XY { { 35, 30 }, { 205, 30 }, { 205, 205 }, { 35, 205 } }
#define TRAMMING_POINT_XY { { 35, 30 }, { 180, 30 }, { 180, 200 }, { 35, 200 } }
#define TRAMMING_POINT_XY { { 35, 200 }, { 35, 30 }, { 180, 30 }, { 180, 200 } }
// Define position names for probe points.
#define TRAMMING_POINT_NAME_1 "Front-Left"
#define TRAMMING_POINT_NAME_2 "Front-Right"
#define TRAMMING_POINT_NAME_3 "Back-Right"
#define TRAMMING_POINT_NAME_4 "Back-Left"
#define TRAMMING_POINT_NAME_1 "Back-Left"
#define TRAMMING_POINT_NAME_2 "Front-Left"
#define TRAMMING_POINT_NAME_3 "Front-Right"
#define TRAMMING_POINT_NAME_4 "Back-Right"
#define RESTORE_LEVELING_AFTER_G35 // Enable to restore leveling setup after operation
//#define REPORT_TRAMMING_MM // Report Z deviation (mm) for each point relative to the first
#define REPORT_TRAMMING_MM // Report Z deviation (mm) for each point relative to the first // MBO: enable
#define ASSISTED_TRAMMING_WIZARD // Add a Tramming Wizard to the LCD menu
@@ -2657,7 +2657,7 @@
// This short retract is done immediately, before parking the nozzle.
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 50 // (mm/s) Unload filament feedrate. This can be pretty fast.
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
#define FILAMENT_CHANGE_UNLOAD_LENGTH 400 // (mm) The length of filament for a complete unload.
#define FILAMENT_CHANGE_UNLOAD_LENGTH 40 // (mm) The length of filament for a complete unload. // MBO: change from 400 to 40
// For Bowden, the full length of the tube and nozzle.
// For direct drive, the full length of the nozzle.
// Set to 0 for manual unloading.
@@ -2666,7 +2666,7 @@
// 0 to disable start loading and skip to fast load only
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 60 // (mm/s) Load filament feedrate. This can be pretty fast.
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 400 // (mm) Load length of filament, from extruder gear to nozzle.
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 40 // (mm) Load length of filament, from extruder gear to nozzle. // MBO: change from 400 to 40
// For Bowden, the full length of the tube and nozzle.
// For direct drive, the full length of the nozzle.
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.