iGoX/3d-printers
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

Prepare firmware modifications for Spite Pro extruder upgrade #19

Merged
iGoX merged 9 commits from igox/ender3-sprite-pro-extruder into main 2025-02-11 19:42:37 +01:00
Conversation 0 Commits 9 Files Changed 2 +43 -33
2 changed files with 43 additions and 33 deletions
Download Patch File Download Diff File Expand all files Collapse all files

48
creality-ender3/Marlin-2.1.2.4/Marlin/Configuration.h
View File

@@ -634,7 +634,8 @@
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
// (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275
// TODO: Change HEATER_0_MAXTEMP to 300 after Sprite Pro extruder upgrade
#define HEATER_0_MAXTEMP 275 // MBO
#define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
@@ -834,8 +835,8 @@
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of flash)
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash) // MBO
#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of flash) // MBO
#endif
// @section safety
@@ -855,7 +856,8 @@
* Note: For Bowden Extruders make this large enough to allow load/unload.
*/
#define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH 600
// TODO: To be decrease with Sprite Pro?
#define EXTRUDE_MAXLENGTH 600 // MBO
//===========================================================================
//======================== Thermal Runaway Protection =======================
@@ -1170,7 +1172,7 @@
//#define ENDSTOP_NOISE_THRESHOLD 2
// Check for stuck or disconnected endstops during homing moves.
//#define DETECT_BROKEN_ENDSTOP
#define DETECT_BROKEN_ENDSTOP // MBO: enable
//=============================================================================
//============================== Movement Settings ============================
@@ -1197,6 +1199,7 @@
* Override with M92
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
*/
// TODO: change e-step (93) to fit Sprite Pro extruder => https://www.youtube.com/watch?v=lH-RrjtiC8M
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 93 }
/**
@@ -1244,7 +1247,7 @@
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define CLASSIC_JERK
//#define CLASSIC_JERK
#if ENABLED(CLASSIC_JERK)
#define DEFAULT_XJERK 10.0
#define DEFAULT_YJERK 10.0
@@ -1515,12 +1518,14 @@
// PROBE_OFFSET with original extruder fans
//#define NOZZLE_TO_PROBE_OFFSET { -44, -14, -2.725 }
// PROBE_OFFSET with SATSANA fangs extruder fans
#define NOZZLE_TO_PROBE_OFFSET { -51, -12, 0 }
// TODO: To be change after Sprite Pro upgrade
#define NOZZLE_TO_PROBE_OFFSET { -51, -12, 0 } // MBO
// Most probes should stay away from the edges of the bed, but
// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
#define PROBING_MARGIN 15
#define PROBING_MARGIN 10 // MBO: change from 15 to 10
// X and Y axis travel speed (mm/min) between probes
#define XY_PROBE_FEEDRATE (133*60)
@@ -1633,8 +1638,8 @@
// Require minimum nozzle and/or bed temperature for probing
//#define PREHEAT_BEFORE_PROBING
#if ENABLED(PREHEAT_BEFORE_PROBING)
#define PROBING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time
#define PROBING_BED_TEMP 50
#define PROBING_NOZZLE_TEMP 150 // (°C) Only applies to E0 at this time // MBO: change from 120 to 150
#define PROBING_BED_TEMP 60 // MBO: change from 50 to 60
#endif
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@@ -1872,7 +1877,8 @@
// After a runout is detected, continue printing this length of filament
// before executing the runout script. Useful for a sensor at the end of
// a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
#define FILAMENT_RUNOUT_DISTANCE_MM 8
// TODO: to be changed after Sprite Pro and new filament sensor installation
#define FILAMENT_RUNOUT_DISTANCE_MM 8 // MBO
#ifdef FILAMENT_RUNOUT_DISTANCE_MM
// Enable this option to use an encoder disc that toggles the runout pin
@@ -1943,10 +1949,10 @@
/**
* Auto-leveling needs preheating
*/
#define PREHEAT_BEFORE_LEVELING
#define PREHEAT_BEFORE_LEVELING // MBO
#if ENABLED(PREHEAT_BEFORE_LEVELING)
#define LEVELING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time
#define LEVELING_BED_TEMP 50
#define LEVELING_BED_TEMP 60 //
#endif
/**
@@ -2150,7 +2156,7 @@
#define HOMING_FEEDRATE_MM_M { (20*60), (20*60), (4*60) }
// Validate that endstops are triggered on homing moves
#define VALIDATE_HOMING_ENDSTOPS
#define VALIDATE_HOMING_ENDSTOPS // MBO: enable
// @section calibrate
@@ -2416,7 +2422,7 @@
*
* View the current statistics with M78.
*/
//#define PRINTCOUNTER
#define PRINTCOUNTER // MBO: enable
#if ENABLED(PRINTCOUNTER)
#define PRINTCOUNTER_SAVE_INTERVAL 60 // (minutes) EEPROM save interval during print. A value of 0 will save stats at end of print.
#endif
@@ -3354,17 +3360,17 @@
#endif
// Support for Adafruit NeoPixel LED driver
#define NEOPIXEL_LED
#define NEOPIXEL_LED // MBO: enable
#if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW, NEO_RGBW, NEO_GRB, NEO_RBG, etc.
// See https://github.com/adafruit/Adafruit_NeoPixel/blob/master/Adafruit_NeoPixel.h
#define NEOPIXEL_PIN PA8 // LED driving pin
#define NEOPIXEL_PIN PA8 // MBO: LED driving pin for BBT SKR E3 Mini v2.0
//#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
//#define NEOPIXEL2_PIN 5
#define NEOPIXEL_PIXELS 17 // Number of LEDs in the strip. (Longest strip when NEOPIXEL2_SEPARATE is disabled.)
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#define NEOPIXEL_PIXELS 17 // Number of LEDs in the strip. (Longest strip when NEOPIXEL2_SEPARATE is disabled.) // MBO: 17
//#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) // MBO: 127
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup // MBO: enable
// Support for second Adafruit NeoPixel LED driver controlled with M150 S1 ...
//#define NEOPIXEL2_SEPARATE

28
creality-ender3/Marlin-2.1.2.4/Marlin/Configuration_adv.h
View File

@@ -1032,23 +1032,25 @@
//
// Add the G35 command to read bed corners to help adjust screws. Requires a bed probe.
//
#define ASSISTED_TRAMMING
#define ASSISTED_TRAMMING // MBO: enable
#if ENABLED(ASSISTED_TRAMMING)
// Define from 3 to 9 points to probe.
//#define TRAMMING_POINT_XY { { 35, 30 }, { 205, 30 }, { 205, 205 }, { 35, 205 } }
#define TRAMMING_POINT_XY { { 35, 30 }, { 180, 30 }, { 180, 200 }, { 35, 200 } }
//#define TRAMMING_POINT_XY { { 35, 200 }, { 35, 30 }, { 180, 30 }, { 180, 200 } }
// TODO: Change after Sprite Pro upgrade
#define TRAMMING_POINT_XY { { 27, 205 }, { 25, 35 }, { 184, 30 }, { 184, 205 } } // MBO
// Define position names for probe points.
#define TRAMMING_POINT_NAME_1 "Front-Left"
#define TRAMMING_POINT_NAME_2 "Front-Right"
#define TRAMMING_POINT_NAME_3 "Back-Right"
#define TRAMMING_POINT_NAME_4 "Back-Left"
#define TRAMMING_POINT_NAME_1 "Back-Left"
#define TRAMMING_POINT_NAME_2 "Front-Left"
#define TRAMMING_POINT_NAME_3 "Front-Right"
#define TRAMMING_POINT_NAME_4 "Back-Right"
#define RESTORE_LEVELING_AFTER_G35 // Enable to restore leveling setup after operation
//#define REPORT_TRAMMING_MM // Report Z deviation (mm) for each point relative to the first
#define REPORT_TRAMMING_MM // Report Z deviation (mm) for each point relative to the first // MBO: enable
#define ASSISTED_TRAMMING_WIZARD // Add a Tramming Wizard to the LCD menu
#define ASSISTED_TRAMMING_WIZARD // Add a Tramming Wizard to the LCD menu // MBO: enable
//#define ASSISTED_TRAMMING_WAIT_POSITION { X_CENTER, Y_CENTER, 30 } // Move the nozzle out of the way for adjustment
@@ -1085,8 +1087,8 @@
* X<1> Set the given parameters only for the X axis.
* Y<1> Set the given parameters only for the Y axis.
*/
#define INPUT_SHAPING_X
#define INPUT_SHAPING_Y
//#define INPUT_SHAPING_X
//#define INPUT_SHAPING_Y
#if EITHER(INPUT_SHAPING_X, INPUT_SHAPING_Y)
#if ENABLED(INPUT_SHAPING_X)
#define SHAPING_FREQ_X 40 // (Hz) The default dominant resonant frequency on the X axis.
@@ -2657,7 +2659,8 @@
// This short retract is done immediately, before parking the nozzle.
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 50 // (mm/s) Unload filament feedrate. This can be pretty fast.
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
#define FILAMENT_CHANGE_UNLOAD_LENGTH 400 // (mm) The length of filament for a complete unload.
// TODO: Change FILAMENT_CHANGE_UNLOAD_LENGTH after Sprite Pro upgrade
#define FILAMENT_CHANGE_UNLOAD_LENGTH 400 // (mm) The length of filament for a complete unload. // MBO
// For Bowden, the full length of the tube and nozzle.
// For direct drive, the full length of the nozzle.
// Set to 0 for manual unloading.
@@ -2666,7 +2669,8 @@
// 0 to disable start loading and skip to fast load only
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 60 // (mm/s) Load filament feedrate. This can be pretty fast.
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 400 // (mm) Load length of filament, from extruder gear to nozzle.
// TODO: Change FILAMENT_CHANGE_FAST_LOAD_LENGTH after Sprite Pro upgrade
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 400 // (mm) Load length of filament, from extruder gear to nozzle. // MBO
// For Bowden, the full length of the tube and nozzle.
// For direct drive, the full length of the nozzle.
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.