# Artillery SideWinder X2

## Klipper Configuration

* Klipper [installation](https://www.klipper3d.org/Installation.html) documentation
* Klipper [printer.cfg](klipper-cfg-files/printer.cfg) file
* Klipper [macros.cfg](klipper-cfg-files/macros.cfg) file

## Ultimaker Cura configuration

### Cura Printer configuration

| Printer | Extruder |
|---------|----------|
| ![printer profile](images/aswx2-cura-profile-printer.png) | ![extruder profile](images/aswx2-cura-profile-extruder.png) |

### Start G-code
```
; Octolapse Plugin required parameters
; Script based on an original created by tjjfvi (https://github.com/tjjfvi)
; An up-to-date version of the tjjfvi's original script can be found
; here:  https://csi.t6.fyi/
; Note - This script will only work in Cura V4.2 and above!
; --- Global Settings
; layer_height = {layer_height}
; smooth_spiralized_contours = {smooth_spiralized_contours}
; magic_mesh_surface_mode = {magic_mesh_surface_mode}
; machine_extruder_count = {machine_extruder_count}
; --- Single Extruder Settings
; speed_z_hop = {speed_z_hop}
; retraction_amount = {retraction_amount}
; retraction_hop = {retraction_hop}
; retraction_hop_enabled = {retraction_hop_enabled}
; retraction_enable = {retraction_enable}
; retraction_speed = {retraction_speed}
; retraction_retract_speed = {retraction_retract_speed}
; retraction_prime_speed = {retraction_prime_speed}
; speed_travel = {speed_travel}

START_PRINT BED_TEMP={material_bed_temperature_layer_0} EXTRUDER_TEMP={material_print_temperature_layer_0}
```

### End G-code
```
END_PRINT
```

### Print profiles

* [Standard Quality](cura-profile/ASWX2%20-%20Standard%20Quality.curaprofile)
* [Dynamic Quality](cura-profile/ASWX2%20-%20Dynamic%20Quality.curaprofile)
* [Low Quality](cura-profile/ASWX2%20-%20Low%20Quality.curaprofile)
* [Super Quality](cura-profile/ASWX2%20-%20Super%20Quality.curaprofile)

## Octoprint specific configuration
### Bed Visualizer plugin configuration
![Bed Visualizer plugin configuration](images/bed-visualizer-plugin-configuration.png)

```
G28
BED_MESH_CALIBRATE
@BEDLEVELVISUALIZER
BED_MESH_OUTPUT
```

## Filament set up
### PLA

| Brand     | Filament desc | Printing temp | Build Plate temp | Retractation Distance |
|-----------|---------------|---------------|------------------|-----------------------|
| Geeetech  | Black         | 205°C         | 60°C             | 0.75mm                |
| Geeetech  | Silk Silver   | 205°C         | 60°C             | 0.75mm                |

### PETG

| Brand     | Filament desc | Printing temp | Build Plate temp | Retractation Distance |
|-----------|---------------|---------------|------------------|-----------------------|
| Geeetech  | --            | --            | --               | --                    |

## Klipper firmware update
### Printer preparation
1. Shutdown the printer

2. Unplug the electrical wall socket

3. Unplug the USB cable labelled `OPERATION` from printer

4. Set the top switch to `UPDATE` position \
![Switch in `UPDATE` position](images/aswx2-switch-in-update-position.jpg)

5. Plug the USB cable labelled `UPDATE` to the printer


### Firmware build and update
1. SSH to the ASWX2 Raspberry

2. Browse to Klipper directory:
```
#> cd ~/klipper
```

3. Git the last version of the Klipper firmware:
```
#> git pull
```

4. Check the firmware build configuration 
```
#> make menuconfig
```
![Klipper firmaware build configuration](images/aswx2-klipper-firmware-config.png)

5. Build the firmaware:
```
#> make
```

6. Check printer's Ruby board is in DFU mode and can be updated 
```
#> lsusb
```
![Ruby board in DFU mode](images/aswx2-ruby-board-DFU-mode-USB.png)

7. Note the Ruby board device ID. In example above: `ID: 0483:df11`

8. Flash the new firmware to the printer's Ruby board using the above device ID:
```
#> make flash FLASH_DEVICE=0483:df11
```
![Klipper firmware flash outputs](images/aswx2-klipper-flash-output.png)

### Switch back printer to operation mode
1. Unplug the USB cable labelled `UPDATE` from printer

2. Set the top switch to `OPERATION` position \
![Switch in `OPERATION` position](images/aswx2-switch-in-operation-position.jpg)

3. Plug the USB cable labelled `OPERATION` to the printer

4. Unplug the electrical wall socket

## Resources / Links

* [Runout sensor bracket SIDEWINDER X2 by LeLudoLAb - Thingiverse](https://www.thingiverse.com/thing:5027268)
* [Schéma pinout Artillery Ruby v1.2 (Genius Pro, Sidewinder X2, Hornet)](https://www.lesimprimantes3d.fr/forum/topic/48552-schéma-pinout-artillery-ruby-v12-genius-pro-sidewinder-x2-hornet/)
* [How to install Klipper on ASWX2 - List of links (Shaarli)](https://shaarli.igox.org/shaare/y5m3Bg)
* [[SW X2] Renforts axe Z - Tutoriels et améliorations pour Artillery - Forum pour les imprimantes 3D et l'impression 3D](https://www.lesimprimantes3d.fr/forum/topic/44553-sw-x2-renforts-axe-z/)
* [[Tuto] Remplacer 3DTouch Artillery par un vrai BLTouch - Tutoriels et améliorations pour Artillery - Forum pour les imprimantes 3D et l'impression 3D](https://www.lesimprimantes3d.fr/forum/topic/46506-tuto-remplacer-3dtouch-artillery-par-un-vrai-bltouch/#comment-484959)
* [Améliorations Sidewinder à imprimer](https://www.abrège.fr/post/ameliorations-sidewinder-x2-a-imprimer)
* [Aide et ressources en français pour imprimantes 3D Artillery](https://docarti.fr/)