OrcaSlicer-bambulab/resources/profiles/PrusaResearch.ini

# Print profiles for the Prusa Research printers.

[vendor]
# Vendor name will be shown by the Config Wizard.
name = Prusa Research
# Configuration version of this file. Config file will only be installed, if the config_version differs.
# This means, the server may force the Slic3r configuration to be downgraded.
config_version = 0.1
# Where to get the updates from?
config_update_url = https://raw.githubusercontent.com/prusa3d/Slic3r-settings/master/live/PrusaResearch.ini

# The printer models will be shown by the Configuration Wizard in this order,
# also the first model installed & the first nozzle installed will be activated after install.
#TODO: One day we may differentiate variants of the nozzles / hot ends,
#for example by the melt zone size, or whether the nozzle is hardened.
[printer_model:MK3]
variants = 0.4; 0.25; 0.6

[printer_model:MK2S]
variants = 0.4; 0.25; 0.6

[printer_model:MK2SMM]
# Printer model name will be shown by the installation wizard.
name = MK2S Multi Material
variants = 0.4; 0.6

# All presets starting with asterisk, for example *common*, are intermediate and they will
# not make it into the user interface.

# Common print preset, mostly derived from MK2 single material with a 0.4mm nozzle.
# All other print presets will derive from the *common* print preset.
[print:*common*]
avoid_crossing_perimeters = 0
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.8
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = 
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeters_first = 0
external_perimeter_extrusion_width = 0.45
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
interface_shells = 0
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
overhangs = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirts = 1
skirt_distance = 2
skirt_height = 3
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_extruder = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_enforce_layers = 0
support_material_interface_contact_loops = 0
support_material_interface_layers = 2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
top_infill_extrusion_width = 0.45
top_solid_infill_speed = 40
travel_speed = 180
wipe_tower = 0
wipe_tower_per_color_wipe = 20
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

# Print parameters common to a 0.25mm diameter nozzle.
[print:*0.25nozzle*]
external_perimeter_extrusion_width = 0.25
extrusion_width = 0.25
first_layer_extrusion_width = 0.25
infill_extrusion_width = 0.25
perimeter_extrusion_width = 0.25
solid_infill_extrusion_width = 0.25
top_infill_extrusion_width = 0.25
support_material_extrusion_width = 0.18
support_material_interface_layers = 0
support_material_interface_spacing = 0.15
support_material_spacing = 1
support_material_xy_spacing = 150%

# Print parameters common to a 0.6mm diameter nozzle.
[print:*0.6nozzle*]
external_perimeter_extrusion_width = 0.61
extrusion_width = 0.67
first_layer_extrusion_width = 0.65
infill_extrusion_width = 0.75
perimeter_extrusion_width = 0.65
solid_infill_extrusion_width = 0.65
top_infill_extrusion_width = 0.6

[print:*soluble_support*]
overhangs = 1
skirts = 0
support_material = 1
support_material_contact_distance = 0
support_material_extruder = 4
support_material_extrusion_width = 0.45
support_material_interface_extruder = 4
support_material_interface_spacing = 0.1
support_material_synchronize_layers = 1
support_material_threshold = 80
support_material_with_sheath = 1
support_material_xy_spacing = 120%
wipe_tower = 1

[print:*0.05mm*]
inherits = *common*
bottom_solid_layers = 10
bridge_acceleration = 300
bridge_flow_ratio = 0.7
default_acceleration = 500
external_perimeter_speed = 20
fill_density = 25%
first_layer_acceleration = 500
gap_fill_speed = 20
infill_acceleration = 800
infill_speed = 30
max_print_speed = 80
small_perimeter_speed = 15
solid_infill_speed = 30
support_material_extrusion_width = 0.3
support_material_interface_spacing = 0.2
support_material_spacing = 1.5
layer_height = 0.05
perimeter_acceleration = 300
perimeter_speed = 30
perimeters = 3
support_material_contact_distance = 0.15
support_material_speed = 30
top_solid_infill_speed = 20
top_solid_layers = 15

[print:0.05mm DETAIL]
inherits = *0.05mm*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders==1
infill_extrusion_width = 0.5

[print:0.05mm DETAIL MK3]
inherits = *0.05mm*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/
fill_pattern = grid
top_infill_extrusion_width = 0.4

[print:0.05mm DETAIL 0.25 nozzle]
inherits = *0.05mm*; *0.25nozzle*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.25 and num_extruders==1
external_perimeter_extrusion_width = 0
extrusion_width = 0.28
fill_density = 20%
first_layer_extrusion_width = 0.3
infill_extrusion_width = 0
infill_speed = 20
max_print_speed = 100
perimeter_extrusion_width = 0
perimeter_speed = 20
perimeters = 4
small_perimeter_speed = 10
solid_infill_extrusion_width = 0
solid_infill_speed = 20
support_material_speed = 20
top_infill_extrusion_width = 0

[print:*0.10mm*]
inherits = *common*
bottom_solid_layers = 7
bridge_flow_ratio = 0.7
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders==1
layer_height = 0.1
perimeter_acceleration = 800
support_material_contact_distance = 0.15
support_material_interface_spacing = 0.2
support_material_spacing = 2
top_solid_layers = 9

[print:0.10mm DETAIL]
inherits = *0.10mm*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders==1
external_perimeter_speed = 40
infill_acceleration = 2000
infill_speed = 60
perimeter_speed = 50
perimeters = 3
solid_infill_speed = 50

[print:0.10mm DETAIL MK3]
inherits = *0.10mm*
bridge_flow_ratio = 0.8
bridge_speed = 30
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/
external_perimeter_speed = 35
fill_pattern = grid
infill_acceleration = 1500
infill_speed = 170
max_print_speed = 170
perimeter_speed = 45
perimeters = 2
solid_infill_speed = 170
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 50

[print:0.10mm DETAIL 0.25 nozzle]
inherits = *0.10mm*; *0.25nozzle*
bridge_acceleration = 600
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.25
external_perimeter_speed = 20
fill_density = 15%
infill_acceleration = 1600
infill_speed = 40
perimeter_acceleration = 600
perimeter_speed = 25
perimeters = 4
small_perimeter_speed = 10
solid_infill_speed = 40
top_solid_infill_speed = 30

[print:*0.15mm*]
inherits = *common*
bottom_solid_layers = 5
external_perimeter_speed = 40
infill_acceleration = 2000
infill_speed = 60
layer_height = 0.15
perimeter_acceleration = 800
perimeter_speed = 50
perimeters = 3
solid_infill_speed = 50
support_material_contact_distance = 0.15
support_material_interface_spacing = 0.2
support_material_spacing = 2
top_infill_extrusion_width = 0.4
top_solid_layers = 7

[print:0.15mm 100mms Linear Advance]
inherits = *0.15mm*
bottom_solid_layers = 4
bridge_flow_ratio = 0.95
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4
external_perimeter_speed = 50
infill_speed = 100
max_print_speed = 150
perimeter_speed = 60
perimeters = 2
small_perimeter_speed = 30
solid_infill_speed = 100
support_material_speed = 60
top_solid_infill_speed = 70
top_solid_layers = 5

[print:0.15mm OPTIMAL]
inherits = *0.15mm*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4
top_infill_extrusion_width = 0.45

[print:0.15mm OPTIMAL 0.25 nozzle]
inherits = *0.15mm*; *0.25nozzle*
bridge_acceleration = 600
bridge_flow_ratio = 0.7
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.25
external_perimeter_speed = 20
infill_acceleration = 1600
infill_speed = 40
perimeter_acceleration = 600
perimeter_speed = 25
perimeters = 2
small_perimeter_speed = 10
solid_infill_speed = 40
support_material_extrusion_width = 0.2
support_material_threshold = 35
top_solid_infill_speed = 30

[print:0.15mm OPTIMAL 0.6 nozzle]
inherits = *0.15mm*; *0.6nozzle*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.6
wipe_tower = 1

[print:0.15mm OPTIMAL MK3]
inherits = *0.15mm*
bridge_speed = 30
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/
external_perimeter_speed = 35
fill_pattern = grid
infill_acceleration = 1500
infill_speed = 170
max_print_speed = 170
perimeter_speed = 45
perimeters = 2
solid_infill_speed = 170
top_solid_infill_speed = 50
wipe_tower = 1

[print:0.15mm OPTIMAL SOLUBLE FULL]
inherits = *0.15mm*; *soluble_support*
bottom_solid_layers = 5
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
external_perimeter_speed = 25
notes = Set your solluble extruder in Multiple Extruders > Support material/raft/skirt extruder &  Support material/raft interface extruder
perimeter_speed = 40
solid_infill_speed = 40
support_material_xy_spacing = 60%
top_infill_extrusion_width = 0.45
top_solid_infill_speed = 30

[print:0.15mm OPTIMAL SOLUBLE INTERFACE]
inherits = 0.15mm OPTIMAL SOLUBLE FULL
notes = Set your solluble extruder in Multiple Extruders >  Support material/raft interface extruder
support_material_extruder = 0
support_material_interface_layers = 3
support_material_with_sheath = 0
support_material_xy_spacing = 120%

[print:*0.20mm*]
inherits = *common*
bottom_solid_layers = 4
bridge_flow_ratio = 0.95
external_perimeter_speed = 40
infill_acceleration = 2000
infill_speed = 60
layer_height = 0.2
perimeter_acceleration = 800
perimeter_speed = 50
perimeters = 2
solid_infill_speed = 50
support_material_contact_distance = 0.15
support_material_interface_spacing = 0.2
support_material_spacing = 2
top_infill_extrusion_width = 0.4
top_solid_layers = 5
wipe_tower = 1

[print:0.20mm 100mms Linear Advance]
inherits = *0.20mm*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4
external_perimeter_speed = 50
infill_speed = 100
max_print_speed = 150
perimeter_speed = 60
small_perimeter_speed = 30
solid_infill_speed = 100
support_material_speed = 60
top_solid_infill_speed = 70

[print:0.20mm FAST MK3]
inherits = *0.20mm*
bridge_speed = 30
bridge_flow_ratio = 0.8
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/
external_perimeter_speed = 35
fill_pattern = grid
infill_acceleration = 1500
infill_speed = 170
max_print_speed = 170
perimeter_speed = 45
solid_infill_speed = 170
top_solid_infill_speed = 50

[print:0.20mm NORMAL]
inherits = *0.20mm*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4

[print:0.20mm NORMAL 0.6 nozzle]
inherits = *0.20mm*; *0.6nozzle*
bridge_flow_ratio = 0.8
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.6
perimeters = 3

[print:0.20mm NORMAL SOLUBLE FULL]
inherits = *0.20mm*; *soluble_support*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4 and num_extruders>1
external_perimeter_speed = 30
notes = Set your solluble extruder in Multiple Extruders > Support material/raft/skirt extruder &  Support material/raft interface extruder
perimeter_speed = 40
solid_infill_speed = 40
top_solid_infill_speed = 30

[print:0.20mm NORMAL SOLUBLE INTERFACE]
inherits = 0.20mm NORMAL SOLUBLE FULL
notes = Set your solluble extruder in Multiple Extruders >  Support material/raft interface extruder
support_material_extruder = 0
support_material_interface_layers = 3
support_material_with_sheath = 0

[print:*0.35mm*]
inherits = *common*
bottom_solid_layers = 3
external_perimeter_extrusion_width = 0.6
external_perimeter_speed = 40
first_layer_extrusion_width = 0.75
infill_acceleration = 2000
infill_extrusion_width = 0.75
infill_speed = 60
layer_height = 0.35
perimeter_acceleration = 800
perimeter_extrusion_width = 0.65
perimeter_speed = 50
perimeters = 2
solid_infill_extrusion_width = 0.65
solid_infill_speed = 60
support_material_contact_distance = 0.15
support_material_interface_spacing = 0.2
support_material_spacing = 2
top_solid_infill_speed = 50
top_solid_layers = 4
wipe_tower = 1

[print:0.35mm FAST]
inherits = *0.35mm*
bridge_flow_ratio = 0.95
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.4
first_layer_extrusion_width = 0.42
infill_extrusion_width = 0.7
perimeter_extrusion_width = 0.43
solid_infill_extrusion_width = 0.7
top_infill_extrusion_width = 0.43

[print:0.35mm FAST 0.6 nozzle]
inherits = *0.35mm*; *0.6nozzle*
bottom_solid_layers = 7
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.6
perimeters = 3
top_solid_layers = 9

[print:0.35mm FAST sol full 0.6 nozzle]
inherits = *0.35mm*; *0.6nozzle*; *soluble_support*
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK2.*/ and nozzle_diameter[0]==0.6 and num_extruders>1
external_perimeter_extrusion_width = 0.6
external_perimeter_speed = 30
notes = Set your solluble extruder in Multiple Extruders >  Support material/raft interface extruder
perimeter_speed = 40
support_material_extrusion_width = 0.55
support_material_interface_layers = 3
support_material_interface_spacing = 0.2
support_material_with_sheath = 0
top_infill_extrusion_width = 0.57

[print:0.35mm FAST sol int 0.6 nozzle]
inherits = 0.35mm FAST sol full 0.6 nozzle
support_material_extruder = 0
support_material_interface_layers = 2
support_material_xy_spacing = 150%

[filament:*common*]
cooling = 1
compatible_printers = 
compatible_printers_condition = 
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_settings_id = 
filament_soluble = 0
min_print_speed = 5
slowdown_below_layer_time = 20
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"

[filament:*PLA*]
inherits = *common*
bed_temperature = 60
bridge_fan_speed = 100
disable_fan_first_layers = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #FF3232
filament_max_volumetric_speed = 15
filament_type = PLA
first_layer_bed_temperature = 60
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 100
temperature = 210

[filament:*PET*]
inherits = *common*
bed_temperature = 90
bridge_fan_speed = 50
disable_fan_first_layers = 3
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #FF8000
filament_max_volumetric_speed = 10
filament_type = PET
first_layer_bed_temperature = 85
first_layer_temperature = 230
max_fan_speed = 50
min_fan_speed = 30
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
temperature = 240

[filament:*ABS*]
inherits = *common*
bed_temperature = 100
bridge_fan_speed = 30
cooling = 0
disable_fan_first_layers = 3
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #3A80CA
filament_max_volumetric_speed = 13
filament_type = ABS
first_layer_bed_temperature = 100
first_layer_temperature = 255
max_fan_speed = 30
min_fan_speed = 10
temperature = 255

[filament:*FLEX*]
inherits = *common*
bridge_fan_speed = 100
compatible_printers_condition = nozzle_diameter[0]>0.35 and num_extruders==1
cooling = 0
disable_fan_first_layers = 1
extrusion_multiplier = 1.2
fan_always_on = 0
fan_below_layer_time = 100
filament_max_volumetric_speed = 1.5
filament_type = FLEX
first_layer_bed_temperature = 50
first_layer_temperature = 240
max_fan_speed = 90
min_fan_speed = 70
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
temperature = 240

[filament:ColorFabb Brass Bronze]
inherits = *PLA*
compatible_printers_condition = nozzle_diameter[0]>0.35
extrusion_multiplier = 1.3
filament_colour = #804040
filament_max_volumetric_speed = 10
min_print_speed = 5

[filament:ColorFabb HT]
bed_temperature = 105
bridge_fan_speed = 30
compatible_printers = 
compatible_printers_condition = 
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 10
filament_colour = #FF8000
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 105
first_layer_temperature = 270
max_fan_speed = 20
min_fan_speed = 10
min_print_speed = 5
slowdown_below_layer_time = 20
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}45{endif}; Filament gcode"
temperature = 270

[filament:ColorFabb PLA-PHA]
inherits = *PLA*
filament_colour = #FF3232

[filament:ColorFabb Woodfil]
inherits = *PLA*
compatible_printers_condition = nozzle_diameter[0]>0.35
extrusion_multiplier = 1.2
filament_colour = #804040
filament_max_volumetric_speed = 10
first_layer_temperature = 200
min_print_speed = 5
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
temperature = 200

[filament:ColorFabb XT]
inherits = *PET*
filament_colour = #FF8000
filament_type = PLA
first_layer_bed_temperature = 90
first_layer_temperature = 260
temperature = 270

[filament:ColorFabb XT-CF20]
inherits = *PET*
extrusion_multiplier = 1.2
filament_colour = #804040
filament_max_volumetric_speed = 1
first_layer_bed_temperature = 90
first_layer_temperature = 260
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"
temperature = 260

[filament:ColorFabb nGen]
inherits = *PET*
bridge_fan_speed = 40
fan_always_on = 0
fan_below_layer_time = 10
filament_colour = #FF8000
filament_type = NGEN
first_layer_temperature = 240
max_fan_speed = 35
min_fan_speed = 20

[filament:ColorFabb nGen flex]
inherits = *flex*
bed_temperature = 85
bridge_fan_speed = 40
cooling = 1
disable_fan_first_layers = 3
extrusion_multiplier = 1
fan_below_layer_time = 10
filament_colour = #FF8000
filament_max_volumetric_speed = 5
first_layer_bed_temperature = 85
first_layer_temperature = 260
max_fan_speed = 35
min_fan_speed = 20
temperature = 260

[filament:E3D Edge]
inherits = *PET*
filament_colour = #FF8000
filament_notes = "List of manufacturers tested with standart PET print settings for MK2:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladeč PETG"

[filament:E3D PC-ABS]
inherits = *ABS*
filament_colour = #3A80CA
first_layer_temperature = 270
temperature = 270

[filament:Fillamentum ABS]
inherits = *ABS*
filament_colour = #3A80CA
first_layer_temperature = 240
temperature = 240

[filament:Fillamentum ASA]
fan_always_on = 1
filament_colour = #3A80CA
first_layer_temperature = 265
temperature = 265

[filament:Fillamentum CPE HG100 HM100]
inherits = *PET*
disable_fan_first_layers = 1
filament_colour = #FF8000
filament_notes = "CPE HG100 , CPE HM100"
first_layer_bed_temperature = 90
first_layer_temperature = 275
max_fan_speed = 50
min_fan_speed = 50
temperature = 275

[filament:Fillamentum Timberfil]
inherits = *PLA*
compatible_printers_condition = nozzle_diameter[0]>0.35
extrusion_multiplier = 1.2
filament_colour = #804040
filament_max_volumetric_speed = 10
first_layer_temperature = 190
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
temperature = 190

[filament:Generic ABS]
inherits = *ABS*
filament_notes = "List of materials tested with standart ABS print settings for MK2:\n\nEsun ABS\nFil-A-Gehr ABS\nHatchboxABS\nPlasty Mladeč ABS"

[filament:Generic PET]
inherits = *PET*
filament_notes = "List of manufacturers tested with standart PET print settings for MK2:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladeč PETG"

[filament:Generic PLA]
inherits = *PLA*
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"

[filament:Polymaker PC-Max]
inherits = *ABS*
bed_temperature = 120
filament_colour = #3A80CA
first_layer_bed_temperature = 120
first_layer_temperature = 270
temperature = 270

[filament:Primavalue PVA]
inherits = *PLA*
cooling = 0
fan_always_on = 0
filament_colour = #FFFFD7
filament_max_volumetric_speed = 10
filament_notes = "List of materials tested with standart PVA print settings for MK2:\n\nPrimaSelect PVA+\nICE FILAMENTS PVA 'NAUGHTY NATURAL'\nVerbatim BVOH"
filament_soluble = 1
filament_type = PVA
first_layer_temperature = 195
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
temperature = 195

[filament:Prusa ABS]
inherits = *ABS*
filament_notes = "List of materials tested with standart ABS print settings for MK2:\n\nEsun ABS\nFil-A-Gehr ABS\nHatchboxABS\nPlasty Mladeč ABS"

[filament:Prusa HIPS]
inherits = *ABS*
bridge_fan_speed = 50
cooling = 1
extrusion_multiplier = 0.9
fan_always_on = 1
fan_below_layer_time = 10
filament_colour = #FFFFD7
filament_soluble = 1
filament_type = HIPS
first_layer_temperature = 220
max_fan_speed = 20
min_fan_speed = 20
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
temperature = 220

[filament:Prusa PET]
inherits = *PET*
filament_notes = "List of manufacturers tested with standart PET print settings for MK2:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladeč PETG"

[filament:Prusa PLA]
inherits = *PLA*
filament_colour = #FF3232
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"

[filament:SemiFlex or Flexfill 98A]
inherits = *flex*

[filament:Taulman Bridge]
bed_temperature = 50
bridge_fan_speed = 40
compatible_printers = 
compatible_printers_condition = 
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #DEE0E6
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 90
first_layer_temperature = 240
max_fan_speed = 5
min_fan_speed = 0
min_print_speed = 5
slowdown_below_layer_time = 20
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
temperature = 250

[filament:Taulman T-Glase]
inherits = *PET*
bridge_fan_speed = 40
cooling = 0
fan_always_on = 0
filament_colour = #FF8000
first_layer_bed_temperature = 90
first_layer_temperature = 240
max_fan_speed = 5
min_fan_speed = 0
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif}; Filament gcode"

[filament:Verbatim BVOH]
bed_temperature = 60
bridge_fan_speed = 100
compatible_printers = 
compatible_printers_condition = 
cooling = 0
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 100
filament_colour = #FFFFD7
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"
filament_settings_id = 
filament_soluble = 1
filament_type = PLA
first_layer_bed_temperature = 60
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 15
slowdown_below_layer_time = 20
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
temperature = 210

[filament:Verbatim PP]
bed_temperature = 100
bridge_fan_speed = 100
compatible_printers = 
compatible_printers_condition = 
cooling = 1
disable_fan_first_layers = 2
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #DEE0E6
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 5
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nEsun PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nEUMAKERS PLA"
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 100
first_layer_temperature = 220
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 15
slowdown_below_layer_time = 20
start_filament_gcode = "M900 K{if printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}10{endif}; Filament gcode"
temperature = 220

[printer:*common*]
bed_shape = 0x0,250x0,250x210,0x210
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\n\n
between_objects_gcode = 
deretract_speed = 0
end_gcode = G4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG1 X0 Y200; home X axis\nM84 ; disable motors
extruder_colour = #FFFF00
extruder_offset = 0x0
gcode_flavor = marlin
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
max_layer_height = 0.25
min_layer_height = 0.07
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\n
printer_settings_id = 
retract_before_travel = 1
retract_before_wipe = 0%
retract_layer_change = 1
retract_length = 0.8
retract_length_toolchange = 3
retract_lift = 0.6
retract_lift_above = 0
retract_lift_below = 199
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 35
serial_port = 
serial_speed = 250000
single_extruder_multi_material = 0
start_gcode = M115 U3.1.0 ; tell printer latest fw version\nM201 X9000 Y9000 Z500 E10000 ; sets maximum accelerations, mm/sec^2\nM203 X500 Y500 Z12 E120 ; sets maximum feedrates, mm/sec\nM204 S1500 T1500 ; sets acceleration (S) and retract acceleration (T)\nM205 X10 Y10 Z0.2 E2.5 ; sets the jerk limits, mm/sec\nM205 S0 T0 ; sets the minimum extruding and travel feed rate, mm/sec\nM83  ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Y-3.0 F1000.0 ; go outside print area\nG92 E0.0\nG1 X60.0 E9.0  F1000.0 ; intro line\nG1 X100.0 E12.5  F1000.0 ; intro line\nG92 E0.0
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0
printer_model = MK2S
printer_variant = 0.4
default_print_profile = 0.15mm OPTIMAL
default_filament_profile = Prusa PLA

[printer:*multimaterial*]
inherits = *common*
deretract_speed = 50
retract_before_travel = 3
retract_before_wipe = 60%
retract_layer_change = 0
retract_length = 4
retract_length_toolchange = 4
retract_lift = 0.6
retract_lift_above = 0
retract_lift_below = 199
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 80
single_extruder_multi_material = 1
printer_model = MK2SMM

[printer:*mm-single*]
inherits = *multimaterial*
end_gcode = G1 E-4 F2100.00000\nG91\nG1 Z1 F7200.000\nG90\nG1 X245 Y1\nG1 X240 E4\nG1 F4000\nG1 X190 E2.7  \nG1 F4600\nG1 X110 E2.8\nG1 F5200\nG1 X40 E3  \nG1 E-15.0000 F5000\nG1 E-50.0000 F5400\nG1 E-15.0000 F3000\nG1 E-12.0000 F2000\nG1 F1600\nG1 X0 Y1 E3.0000\nG1 X50 Y1 E-5.0000\nG1 F2000\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-5.0000\nG1 F2400\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-5.0000\nG1 F2400\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-3.0000\nG4 S0\nM107 ; fan off\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nG28 X0  ; home X axis\nM84     ; disable motors\n\n
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\nPRINTER_HAS_BOWDEN
start_gcode = M115 U3.1.0 ; tell printer latest fw version\nM201 X9000 Y9000 Z500 E10000 ; sets maximum accelerations, mm/sec^2\nM203 X500 Y500 Z12 E120 ; sets maximum feedrates, mm/sec\nM204 S1500 T1500 ; sets acceleration (S) and retract acceleration (T)\nM205 X10 Y10 Z0.2 E2.5 ; sets the jerk limits, mm/sec\nM205 S0 T0 ; sets the minimum extruding and travel feed rate, mm/sec\n; Start G-Code sequence START\nT?\nM104 S[first_layer_temperature]\nM140 S[first_layer_bed_temperature]\nM109 S[first_layer_temperature]\nM190 S[first_layer_bed_temperature]\nG21 ; set units to millimeters\nG90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\nG28 W\nG80\nG92 E0.0\nM203 E100\nM92 E140\nG1 Z0.250 F7200.000\nG1 X50.0 E80.0  F1000.0\nG1 X160.0 E20.0  F1000.0\nG1 Z0.200 F7200.000\nG1 X220.0 E13 F1000.0\nG1 X240.0 E0 F1000.0\nG1 E-4 F1000.0\nG92 E0.0

[printer:*mm-multi*]
inherits = *multimaterial*
end_gcode = {if not has_wipe_tower}\n; Pull the filament into the cooling tubes.\nG1 E-4 F2100.00000\nG91\nG1 Z1 F7200.000\nG90\nG1 X245 Y1\nG1 X240 E4\nG1 F4000\nG1 X190 E2.7  \nG1 F4600\nG1 X110 E2.8\nG1 F5200\nG1 X40 E3  \nG1 E-15.0000 F5000\nG1 E-50.0000 F5400\nG1 E-15.0000 F3000\nG1 E-12.0000 F2000\nG1 F1600\nG1 X0 Y1 E3.0000\nG1 X50 Y1 E-5.0000\nG1 F2000\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-5.0000\nG1 F2400\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-5.0000\nG1 F2400\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-3.0000\nG4 S0\n{endif}\nM107 ; fan off\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nG28 X0  ; home X axis\nM84     ; disable motors
extruder_colour = #FFAA55;#5182DB;#4ECDD3;#FB7259
nozzle_diameter = 0.4,0.4,0.4,0.4
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK2\nPRINTER_HAS_BOWDEN
start_gcode = M115 U3.1.0 ; tell printer latest fw version\nM201 X9000 Y9000 Z500 E10000 ; sets maximum accelerations, mm/sec^2\nM203 X500 Y500 Z12 E120 ; sets maximum feedrates, mm/sec\nM204 S1500 T1500 ; sets acceleration (S) and retract acceleration (T)\nM205 X10 Y10 Z0.2 E2.5 ; sets the jerk limits, mm/sec\nM205 S0 T0 ; sets the minimum extruding and travel feed rate, mm/sec\n; Start G-Code sequence START\nT[initial_tool]\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG21 ; set units to millimeters\nG90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\nG28 W\nG80\nG92 E0.0\nM203 E100 ; set max feedrate\nM92 E140 ; E-steps per filament milimeter\n{if not has_wipe_tower}\nG1 Z0.250 F7200.000\nG1 X50.0 E80.0  F1000.0\nG1 X160.0 E20.0  F1000.0\nG1 Z0.200 F7200.000\nG1 X220.0 E13 F1000.0\nG1 X240.0 E0 F1000.0\nG1 E-4 F1000.0\n{endif}\nG92 E0.0
variable_layer_height = 0

[printer:Original Prusa i3 MK2]
inherits = *common*

[printer:Original Prusa i3 MK2 0.25 nozzle]
inherits = *common*
max_layer_height = 0.1
min_layer_height = 0.05
nozzle_diameter = 0.25
retract_length = 1
retract_speed = 50
variable_layer_height = 0
printer_variant = 0.25
default_print_profile = 0.10mm DETAIL 0.25 nozzle

[printer:Original Prusa i3 MK2 0.6 nozzle]
inherits = *common*
max_layer_height = 0.35
min_layer_height = 0.1
nozzle_diameter = 0.6
printer_variant = 0.6

[printer:Original Prusa i3 MK2 MM Single Mode]
inherits = *mm-single*

[printer:Original Prusa i3 MK2 MM Single Mode 0.6 nozzle]
inherits = *mm-single*
nozzle_diameter = 0.6
printer_variant = 0.6

[printer:Original Prusa i3 MK2 MultiMaterial]
inherits = *mm-multi*
nozzle_diameter = 0.4,0.4,0.4,0.4

[printer:Original Prusa i3 MK2 MultiMaterial 0.6 nozzle]
inherits = *mm-multi*
nozzle_diameter = 0.6,0.6,0.6,0.6
printer_variant = 0.6

[printer:Original Prusa i3 MK3]
inherits = *common*
end_gcode = G4 ; wait\nM221 S100\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG1 X0 Y200; home X axis\nM84 ; disable motors
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK3\n
retract_lift_below = 209
start_gcode = M115 U3.1.1-RC5 ; tell printer latest fw version\nM201 X1000 Y1000 Z200 E5000 ; sets maximum accelerations, mm/sec^2\nM203 X200 Y200 Z12 E120 ; sets maximum feedrates, mm/sec\nM204 S1250 T1250 ; sets acceleration (S) and retract acceleration (T)\nM205 X10 Y10 Z0.4 E2.5 ; sets the jerk limits, mm/sec\nM205 S0 T0 ; sets the minimum extruding and travel feed rate, mm/sec\nM83  ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Y-3.0 F1000.0 ; go outside print area\nG92 E0.0\nG1 X60.0 E9.0  F1000.0 ; intro line\nG1 X100.0 E12.5  F1000.0 ; intro line\nG92 E0.0\nM221 S{if layer_height==0.05}100{else}95{endif}
printer_model = MK3
default_print_profile = 0.15mm OPTIMAL MK3