Full OrcaSlicer config for Ender3 & ASWX4P

OrcaSlicer/system/Artillery/machine/Artillery Genius 0.4 nozzle.json

@@ -0,0 +1,116 @@
+{
+    "type": "machine",
+    "setting_id": "GM003",
+    "name": "Artillery Genius 0.4 nozzle",
+    "from": "system",
+    "instantiation": "true",
+    "inherits": "fdm_machine_common",
+    "printer_model": "Artillery Genius",
+    "default_print_profile": "0.20mm Standard @Artillery Genius",
+    "nozzle_diameter": [
+        "0.4"
+    ],
+    "bed_exclude_area": [
+      "0x0"
+    ],
+    "printable_area": [
+      "0x0",
+      "220x0",
+      "220x220",
+      "0x220"
+    ],
+    "printable_height": "250",
+	"nozzle_type": "brass",
+	"auxiliary_fan": "0",
+	"machine_max_acceleration_extruding": [
+		"1000",
+		"1250"
+	],
+	"machine_max_acceleration_retracting": [
+		"1000",
+		"1250"
+	],
+	"machine_max_acceleration_travel": [
+		"1000",
+		"1250"
+	],
+	"machine_max_acceleration_x": [
+		"2000",
+		"1000"
+	],
+	"machine_max_acceleration_y": [
+		"2000",
+		"1000"
+	],
+	"machine_max_acceleration_z": [
+		"500",
+		"200"
+	],
+	"machine_max_speed_e": [
+		"120",
+		"120"
+	],
+	"machine_max_speed_x": [
+		"500",
+		"200"
+	],
+	"machine_max_speed_y": [
+		"500",
+		"200"
+	],
+	"machine_max_speed_z": [
+		"12",
+		"12"
+	],
+	"machine_max_jerk_e": [
+		"3",
+		"2.5"
+	],
+	"machine_max_jerk_x": [
+		"7",
+		"10"
+	],
+	"machine_max_jerk_y": [
+		"7",
+		"10"
+	],
+	"machine_max_jerk_z": [
+		"0.2",
+		"0.4"
+	],
+	"max_layer_height": [
+		"0.32"
+	],
+	"min_layer_height": [
+		"0.08"
+	],
+	"printer_settings_id": "Artillery",
+	"retraction_minimum_travel": [
+		"1"
+	],
+	"retract_before_wipe": [
+		"0%"
+	],
+	"retraction_length": [
+		"1"
+	],
+	"retract_length_toolchange": [
+		"4"
+	],
+	"retraction_speed": [
+		"35"
+	],
+	"deretraction_speed": [
+		"0"
+	],
+	"single_extruder_multi_material": "1",
+	"change_filament_gcode": "",
+	"machine_pause_gcode": "M0",
+	"default_filament_profile": [
+		"Artillery Generic PLA"
+	],
+    "machine_start_gcode": "M83; extruder relative mode\nG28; home all axes\nM109 S[nozzle_temperature_initial_layer]; hotend temperature\nM140 S[bed_temperature_initial_layer_single]; heatbed temperature\nM190 S[bed_temperature_initial_layer_single]; wait for the bed to heat up\nM109 S[nozzle_temperature_initial_layer]; wait for the extruder to heat up\nG92 E0; reset extruder\nG1 X20 Y5 Z0.3 F5000.0; move to start-line position\nG1 Z0.3 F1000; print height\nG1 X200 Y5 F1500.0 E15; draw 1st line\nG1 X200 Y5.3 Z0.3 F5000.0; move to side a little\nG1 X5.3  Y5.3 Z0.3 F1500.0 E30; draw 2nd line\nG1 Z3 F3000; move z up little to prevent scratching of surface",
+    "machine_end_gcode": "G91; Relative positionning\nG1 E-2 Z0.2 F2400; Retract and raise Z\nG1 X5 Y5 F3000; Wipe out\nG1 Z10; Raise Z more\nG90; Absolute positionning\nG1 X0 Y100; Present print\nM106 S0; Turn-off fan\nM104 S0; Turn-off hotend\nM140 S0; Turn-off bed\nM84 X Y E; Disable all steppers but Z",
+    "layer_change_gcode": "",
+    "scan_first_layer": "0"
+}